Aquastop SHT 226
Item no.: 300228
The Aquastop SHT 226 is a protection system with device shutdown. The electronic alarm and shutdown device detects the smallest amounts of liquid and switches off the connected device.
Possible applications
- Detection of water level changes (at least 4 cm)
- also for other liquids (e.g. fuel oil, diesel, vegetable oil, lubricating oil, etc.)
CO ALARM GX-C3pro
Item no.: 300229
The socket CO warning device with external sensor for carbon monoxide is plugged into a socket and the sensor is placed at average nose level. The warning device is ready for operation after 5 minutes and warns with the alarm thresholds specified in DIN standard 50291 with an alarm tone and a red flashing LED. In the event of an alarm, the device connected to the GX-C3pro, e.g. a gas heater, is also reliably switched off, whereby the device remains switched off until the user has ensured that his ventilation measures have had an effect and he resets the device by briefly unplugging it and plugging it back into the socket.
Possible applications
- Monitoring in case of leakage of carbon monoxide from all heat generating equipment in apartments, houses, stores, ...
- Monitoring of all gas-operated systems and safety shutdown in the event of elevated CO levels
- for gas heaters, gas heating, gas cookers, gas furnaces, oil heating and any combustion facility with supply
- Can also be used in the bathroom and other damp rooms as long as moisture does not condense
- Designed for years of continuous operation
GAS ALARM GX-CO-12
Item no.: 300712
Areas of application
- mobile use in camping vehicles and on ships
- Camper, caravan
- other recreational vehicles with gas cooking and cooling facilities
- boiler room with gas heating or boiler
Cable exhaust control KDS 210 DIBt
Item no.: 300672
The magnetic switch of the KDS 210 set with DIBt approval monitors the window position and transmits the information via a thin cable to an intermediate plug control unit with a switched 5 A socket. In this way, an exhaust air system can only be operated with a tilted or open window if it is ensured that sufficient fresh air flows into the room and thus no negative pressure is created that could draw dangerous and toxic carbon monoxide from a combustion site.
Possible applications
- Fume cupboard control
- Exhaust air control
- for trough fans is only KDS 110 suitable
Radio climate control FKS 100
Item no.: 301268
Do not cool and heat out the window!
The transmitter of the FKS 100 set monitors the window position and transmits the information by radio to a built-in receiver with potential-free 5 A changeover relay. In this way, an air conditioner can be switched off automatically when the window is tilted or open, so that the outside air is not cooled and energy is wasted unnecessarily.
Comfort package FDS 200 / FTX 519
Item no.: 300549This comfort package without DIBt approval includes a classic FDS 200 extract air control set consisting of a radio window switch with intermediate plug receiver and an FTX flue gas temperature monitor with remote transmitter for shorter or covered but always freely accessible stovepipes. This means that for very rarely used stoves, a window does not always have to be opened every time the exhaust air system is used.
Starting current limiter ASB 116 2500W/10A
Item no.: 300116
Water detector SHT 240
Item no.: 300240
PROFI CO ALARM GX-C300
Item no.: 300255
Professional carbon monoxide warning device for fixed installation with warning levels and alarm delay times as specified in the DIN EN 50291 standard. Display of the exact measured CO concentrations in ppm on an illuminated plain text display. In case of alarm and in case of technical faults detected by the device itself, one potential-free change-over relay each switches to activate e.g. forced ventilation or to inform the BMS. The internal electrochemical sensor has a service life of 6 to 10 years, depending on the ambient conditions, and can easily be replaced by Elektrotechnik Schabus at the factory.
Aqua Scanner SHT 5020
Item no.: 300746
The Aqua Scanner SHT 5020 is a 2 meter long sensor (extendable on request), sensitive to single drops of water along its entire length. The mechanically strong cable, resistant to corrosion and abrasion, consists of two sensor wires embedded in a fluoropolymer carrier rod. Due to the robust cable construction with conductive polymer technology and fluoropolymer construction detection, no metal is exposed. For cleaning, you can wipe it with a clean damp cloth.
For connection to the Schabus water detectors is suitable only a LiYY control line with 2x 0.14mm², which can be ordered separately.
Possible applications
- Accessories for SCHABUS water detectors SHT 5000, 5001 and 5002
- 100% made in Germany
- for laying under kitchen and bathroom furniture
- under aquariums
- under other devices, where water can leak over a wide area
- under pipes, tubs, tanks ...
- for indoor projects such as data centers / control rooms / HVAC / IOT
Water detector SHT 5002
Item no.: 300749
The SHT 5002 water detector for top-hat rail mounting in the fuse box or small distribution board is designed as a level controller and has 2 different detection lines. Detection line 1 is the actual level controller, which receives the functions "Fill" or "Drain" by means of a wire jumper and switches its potential-free 5 A changeover relay depending on a lower and an upper level, each of which is defined by a mini float switch. Detection line 2 works like a simple water detector and is called "overflow detector" here, i.e. as soon as water is detected by a sensor or mini-float switch, the second relay of the SHT 5002 switches over.
CO2 traffic light "Medical
Item no.: 400350
The CO2 traffic light "medical" with wall mount and plug-in power supply is our most sensitive version, which already switches to yellow at 800 ppm CO2, from 1200 ppm CO2 to red and from 2000 ppm CO2 to red flashing with alarm tone. It is therefore ideally suited for monitoring rooms in which many people with special physiological restrictions are often present, e.g. waiting rooms in doctors' surgeries or senior residences.
Possible applications
- Surveillance of doctors' surgeries, hospitals, old people's homes, etc.
- for all rooms where people spend long periods of time on a regular basis
- Reliable reminder for regular draught ventilation
GAS ALARM GX-D2
Item no.: 300252The plug-in CO2 warning device with external sensor for carbon dioxide is simply plugged into a socket and the sensor is placed in an upper (more tolerant) or lower (more sensitive) position depending on the desired sensitivity. It is ready for operation after 3 minutes of preheating time and warns when half the MAC (2500 ppm) is reached with a loud alarm tone and red flashing LED.
GX-CO2-30 Carbon dioxide gas sensor
Item no.: 300315
Ext. CO2 sensor for carbon dioxide - from technical equipment
The external CO2 sensor with its own alarm transmitter, status LEDs and test button is optimized as an accessory for the SCHABUS gas warning devices GX-HS and GX-A1+ is oriented with its warning levels and protection class IP54 to the beverage dispensing system regulation.
Radio receiver FGS 170-E
Item no.: 300701
Pump control SHT 227
Item no.: 300227
The water detector for pump control!
The SHT 227 socket water detector functions as a pump control. If a certain water level is detected with the mini float switch, the socket switches on the connected pump and an alarm sounds. After the water level drops below the specified level, the pump continues to run for an adjustable follow-up time of 0 to 100 seconds, is then switched off and the alarm stops again.
Possible applications
- Water ingress
- Pump sump
- Cistern monitoring
- Also suitable for other liquids (e.g. heating oil, diesel, vegetable oil, lubricating oils, etc.)
Gas sensor GX-CO
Item no.: 200898-CO
GX-D11
Item no.: 400311
The plug-in CO2 traffic light with internal NDIR sensor, the LED displays red, yellow and green, as well as discreet acoustic support, is used in areas where a reminder for regular ventilation is necessary, but people present should not be unsettled by yellow and red warning colours that are visible from afar.
Radio climate control FKS 200
Item no.: 301462
The transmitter of the FKS 200 set monitors the window position and transmits the information by radio to an adapter plug receiver with a switched 5 A socket. In this way, an air conditioner can be switched off automatically when a window is tilted or open, so that the outside air is not cooled and energy is wasted unnecessarily.
GAS ALARM GX-B1pro
Item no.: 300924
The socket gas warning device with internal sensor for town gas and natural gas is plugged into an upper (natural gas / methane) or lower (liquid gas / butane, propane) socket depending on the gas, is ready for operation after 3 minutes preheating time and warns already far below dangerous gas concentrations with a loud alarm tone and red flashing LED.
Possible applications
- Monitoring of gas heating or gas cooker / detection of town, natural and liquid gases
- Monitoring of the heating and utility rooms
- Storage of liquid gas cylinders or camping gas
- Air conditioners / coolants
PROF. CO ALARM GX-C300P
Item no.: 300256Professional carbon monoxide warning device for permanent installation with warning levels and alarm delay times as specified in the DIN EN 50291 standard and suction device by means of a silicone hose to monitor thermally demanding rooms (e.g. gas-operated sauna). Display of the exact measured CO concentrations in ppm on an illuminated plain text display. In the event of an alarm and technical faults detected by the unit itself, a potential-free changeover relay switches in each case, e.g. to activate forced ventilation or to inform the BMS. The internal electrochemical sensor has a service life of 6 to 10 years, depending on the ambient conditions, and can easily be replaced by Elektrotechnik Schabus at the factory.
Gas sensor GX-CFC for refrigerant
Item no.: 200901
Supply air damper electric ⌀ 100 mm
Item no.: 201756
The electric supply air damper with a diameter of 100 mm and a fast spring return motor opens within 8 seconds when the operating voltage is applied and closes, also braked by the spring gear, in about 8 seconds when the operating voltage is removed. Such a damper is controlled e.g. by the KZS 200 (301745) supply air control, which automatically opens the damper when the exhaust air motor is switched on.
Possible applications
- Supply air control for extractor bonnet
- For controlling the air flow in ventilation and air-conditioning systems
- Diameter: Ø100 mm
Folding float switch 230 volt
Item no.: 300949
GX-D500P
Item no.: 300263
Possible applications
- Dry ice processing/storage
- Beverage dispensing systems and greenhouses
- Meat and sausage cooling
- according to DIN 6653-2
- Automatic forced ventilation
- Rooms with very hot, cold, humid or dusty air or in ventilation systems with draughts
CO detector according to DIN EN 50291
Item no.: 7549937
Radio exhaust air control FDS 216
Item no.: 300460
The transmitter of the FDS 216 set without DIBt approval monitors the window position and transmits the information by radio to an intermediate plug receiver with a switched 16 A socket. In this way, an exhaust air system can only be operated with a tilted or open window if it is ensured that sufficient fresh air flows into the room and thus no negative pressure is created that could draw dangerous and toxic carbon monoxide from a combustion site.
Possible applications
- Fume cupboard control
- Exhaust air tumble dryer
- Simple receiver installation in seconds
WWD 100 Wireless Water Detector
Item no.: 200100
Supply air damper electric ⌀ 150 mm
Item no.: 201755
The electric supply air damper with a diameter of 150 mm and a fast spring return motor opens within 8 seconds when the operating voltage is applied and closes, also braked by the spring gear, in about 8 seconds when the operating voltage is removed. Such a damper is controlled, for example, by the KZS 200 (301745) supply air control unit, which automatically opens the damper when the exhaust air motor is switched on.
Possible applications
- Supply air control for extractor bonnet
- For controlling the air flow in ventilation and air-conditioning systems
Starting current limiter ASB 120 3500W/16A
Item no.: 300118
The ASB 120 starting current limiter limits the current of a machine starting in no-load operation the machine connection power for about 700 milliseconds immediately after it is switched on and then switches the current fully through in order to effectively prevent the house circuit breaker on the public power supply system from tripping during the time phase in which the magnetic field of the coils of an electric motor has not yet been established.
Silicone hose
Item no.: 21002
GAS ALARM SET GX-A1+CO
Item no.: 300266
We have designed the GX-A1+CO set in such a way that it is possible to equip a professional carbon monoxide warning device with an external sensor, e.g. to position the warning device in front of the room to be monitored and the sensor in the room to be monitored in order to see from the outside whether the room is safe to enter.
The carbon monoxide concentration is evaluated and displayed with ppm accuracy. In the event of an alarm, a potential-free changeover relay switches and another relay switches in the event of technical faults detected by the warning device itself, such as a cable break or sensor failure, in order to inform the building control system.
Possible applications
- Carbon monoxide CO from incomplete combustion
- open fireplace, gas stoves, Swedish stoves
- Open fire, barbecue facilities, pellet bunker
Ball protection grid for CO2 traffic light
Item no.: 300947
CO2 ALARM GX-D1
Item no.: 300251The plug-in CO2 warning device with internal sensor for carbon dioxide is plugged into an upper (tolerant) or lower (sensitive) socket depending on the desired sensitivity, is ready for operation after 3 minutes preheating time and warns when half the MAC (2500 ppm) is reached with a loud alarm tone and red flashing LED.
Possible applications
- Monitoring of medical practices, waiting rooms, open-plan offices, workshops, etc.
- for all rooms where people spend long periods of time on a regular basis
- by the exclus. acoust. Warning ideal for waiting rooms or the like where a visual warning could irritate
- Reliable reminder to air regularly
Cable supply air control KZS 200
Item no.: 301745
The intermediate plug of the cable supply air control KZS 200 is plugged in between the cooker hood and the socket and detects whether only the light of the hood or also the exhaust air motor is switched on by means of a consumption value adjustable from 5 to 250 watts. If the device detects a running motor, a supply air flap is opened via the line and also closed again after the exhaust air motor is switched off. The KZS 200 control unit is available for both variants of the Supply air dampers suitable for the slow but powerful Belimo motor of the airtight dampers as well as for the fast spring-return motor of the plastic dampers.
Possible applications
Hint:
Involve your chimney sweep in your planning before installation so that nothing stands in the way of acceptance afterwards. There are significant regional differences over which Elektrotechnik Schabus has no influence.
- Extractor fan control (independent of lighting)
- Supply air dampers
Gas sensor GX-CO2-25
Item no.: 200989External, active CO2 sensor with its own alarm, LEDs and test button, for connection to the warning devices GX-A1+ or GX-HS, detects CO2 from used air or CO2 exhaled by people, as a timely reminder to ventilate at about half the MAC (2500 ppm).
Performance features
- External sensor for the gas detectors GX-A1 and GX-HS
- Mains operation also possible without warning device
- Detection of carbon dioxide(CO2): Reminder to ventilate regularly
Float switch
Item no.: 200983
Water sensor SHT 5090
Item no.: 300721
Supply air damper electric ⌀ 200 mm
Item no.: 201752
The electric supply air damper with a diameter of 200 mm and a fast spring return motor opens within 8 seconds when the operating voltage is applied and closes, also braked by the spring gear, in about 8 seconds when the operating voltage is removed. Such a damper is controlled, for example, by the KZS 200 (301745) supply air control unit, which automatically opens the damper when the exhaust air motor is switched on.
Possible applications
- Supply air control for extractor bonnet
- For controlling the air flow in ventilation and air-conditioning systems
PROF. GAS ALARM GX-C300S
Item no.: 300265
The professional carbon monoxide warning device with internal CO sensor, whose measuring cell, evaluation electronics and software have been tested by TÜV Süd according to the standard, is here equipped with an additional external city and natural gas sensor, which makes the entire system the perfect warning device for the boiler room in which a gas heating system or boiler is installed. The alarm relay, which is energised in monitoring mode, drops out when gas is detected (methane, butane, propane, ethanol) or when the CO concentration specified by the standard is exceeded, and can thus switch off the heating system with its solenoid shut-off valve in the event of danger to reliably prevent further inflow of toxic or flammable gases.
